Question - What is Stainless Steel 202 Flat Bar?
Nascent Pipe and Tubes is one of the leading supplier, exporter, traders and stock holder of Stainless Steel 202 Flat Bar. Stainless Steel 202 Flat Bar is the most economical stainless flat. Stainless steel 202 Flat Bar is a basic of building support material. They are generally used for support braces, ladder hangers, gate, doors, and bracing. The machinability of grade Stainless Steel 202 Flat Bar produces long, gummy chips. Machining can also be performed in the annealed condition. Type Stainless Steel 202 Flat Bar is an austenitic chromium-nickel-manganese stainless steel which was developed to conserve nickel. Type Stainless Steel 202 Flat Bar is a lower cost alternative to conventional Cr-Ni stainless steels such as 301 and 304. Nickel is replaced by additions of manganese and nitrogen. Stainless Steel 202 Flat Bar is non-hard enable by thermal treatment, but may be cold worked to high tensile strengths. Type 201 is essentially nonmagnetic in the annealed condition and becomes magnetic when cold worked. Type 201 can be substituted for Type 301 in many applications.
Application for Stainless Steel 202 Flat Bar -
The Stainless Steel 202 Flat Bar can be made into plates, sheets, and coils to be used in the following.
Stainless Steel 202 flat Bar coil
Type Stainless Steel flat Bar202 can be welded by all conventional methods applied to 18 percent chromium, 8 percent nickel steels. Filler metal of the conventional chromium-nickel analyses can be used. Like other austenitic stainless steels where carbon is not controlled below 0.03%, Type Stainless Steel 202 Flat Bar 202 is susceptible to intergranular corrosion in the weld heat affected zone.
Stainless Steel 202 Flat bar coil Corrosion -
It is one of the most widely used precipitation hardening grades, and possesses good corrosion resistance, toughness, high harness, and strength. The following datasheet provides an overview of grade Stainless Steel 202 Flat Bar Stainless steel. Type Stainless Steel 202 flat Bar is resistant to a wide variety of mild to moderately corrosive environments. It has corrosion resistance approaching that of Types 301and has been successfully substituted for 304 in many mild environments Stainless Steel 202 Flat Bar coils Thickness Range: -0.025mm – 4.00mm. Stainless Steel 202 Flat Bar coils Width : -Soft, Half Hard, Half Hard, ¾ Hard, Full Hard & Spring Hard Stainless steel 202 coils Hardness: - Minimum 3.2mm to maximum 2000mm. Stainless Steel 202 flat Bar coils Finish: - 2B, 2D, Bright Annealed, #3 Polish, #4 Polish and more.
Stainless Steel 202 Flat Bar has similar bending, forming and drawing characteristics to Type 301 stainless steel. Introduction - Grade Stainless Steel 202 Flat Bar is a type of Cr-Ni-Mn stainless with similar properties to A240/SUS 302 stainless steel. The toughness of grade Stainless Steel 202 Flat Barat low temperatures is excellent.
Question - What is Aluminum Sheets used for?
Nascent Pipe and Tubes is one of the leading supplier, exporter and stock holder of Aluminum Sheets. The Aluminum Sheets are the most widely used form of Aluminum, Aluminum sheets are found in all aluminum industry's major markets.
Aluminum Sheets are used to manufacturers panels for auto mobile bodies and tractor trailers. Aluminum Sheets are used in home appliances and cookware. Aluminum Sheets can be shaped with a finishing hammers depending. The main reason to use Aluminum Sheets material is its combination of light weight and high strength. Thought the Aluminum steel alloys is lower than that of steel, the light weight of the material allows for the use of thicker gauges that may compensate for the reduction in strength. As pure Aluminum Sheets possesses a relatively greater resistance to corrosion over the majority of Aluminum alloys, it was soon recognized that a thin coating of pure Aluminum Sheets over the exterior surface of those alloys would take advantage of the superior qualities of both materials. Thus, a key advantage of Alclad over most Aluminum Sheets alloys is its high corrosion resistance. However, considerable care must be taken while working on an Alclad-covered exterior surface, such as while cleaning the skin of an aircraft, to avoid scarring the surface to expose the vulnerable alloy underneath and prematurely age those elements. The best type of aluminium sheet depends on your application, as it comes in a range of sizes, thicknesses, strengths and finishes. Get in touch with our experts to find out which type of Aluminum Sheets metal is most suitable for your project.
Question - What is Stainless Steel Bright Bar?
Nascent Pipe and Tubes is one of the leading supplier, exporter, traders and stock holder of Stainless Steel Bright Bar. Stainless Steel Bright bar is steel bars which are geometrically in precise shape and have tolerance which is tight dimensional. Stainless Steel Bright bars surface finish is smooth and shiny, which appears to be bright. Stainless Steel Bright Bar are steel bars which are geometrically in precise shape and have tolerance which is tight dimensional. Its surface finish is smooth and shiny, which appears to be bright. Stainless Steel Bright Bar have several uses and applications. They are available in rounds, flats, hexagons, and squares. Stainless Steel Bright Bar is crafted in many grades and different process of manufacturing is used depending on the form of application and designs. Bright bars are manufactured in ultimate quality, which is why they are so popular with our clients. We produce Industrial grade Stainless Steel Bright Bar in Carbon steel, mild steel, Case nitriding and hardening, Micro alloyed, alloy steel, graded steel, free cuts which are carbon free or customized bright bars according to client’s requirement. Our steel plant Stainless Steel Bright Bar is fitted with ultra modern production technologies which go through modern processes of making steel. High quality manufacturing process teamed up with modern facilities has provided us the reputation of being top-rate manufacturers and exporters in the country.
Stainless Steel Bright Bar -
Our manufacturing unit has facilities like testing the materials, straightness conformity, cutting the bars according to particular size, grinding, weight accuracy, proper test certificates, coil to coil drawing, accurate documentation and prompt deliveries. We have quality check performed during each step of production and the storage is done in proper manner to ensure delivery of finest quality goods. Stainless Steel Bright Bars are in high demand for making different types of fastener products like bolts, nuts, pins, and rivets. These could be micro-size to mega-size, depending upon the application and custom requirements. The Stainless Steel Bright Bars in round shape is a perfect base material for machining and making these fasteners that are used in ambiances or the domestic applications. Stainless Steel Bright Bars in different shapes and sizes are directly in use for manufacturing the machine components like the smaller ones used in automobile engines. The manufacturers are supplying very high-quality SS base products to the ancillaries and brands for making these machine components. Stainless Steel Bright Bar is crafted in many grades and different process of manufacturing is used depending on the form of application and designs. Bright bars are manufactured in ultimate quality, which is why they are so popular with our clients. Different grades of Stainless Steel Bright Bars in flats, squares, and rounds, are used in automobile frames and chassis. All such uses of Stainless Steel bright bars have emerged because of the precise dimensions in which these products are made available by the manufacturers. The applications mentioned above have the common demands for accuracy and stability, which is ensured through the quality Stainless Steel Bright Bar.
Question - What is Benefit of Stainless Steel Rivet?
Nascent Pipe and Tubes is a Leading supplier and stock holder of Stainless Steel Rivet. Stainless Steel Rivet available in a different sizes and shapes such as solid rivets and blind rivets. Closed-end stainless steel blind rivets specifically are air and water tight, making them an ideal solution. Depending on your application, you can opt for low-carbon Stainless Steel Rivets or higher-carbon steel Rivet. Low-carbon Stainless Steel Rivet is most often used in projects that require good rivet formability because these rivets give more clinch-over in your application. High-carbon steel, on the other hand, is used when the strength and hardness of the rivet is of the utmost importance, such as in locomotive manufacturing. They actually gain more strength as they are clinched during installation. The formability of these types of rivets is lower, however, and they’re hardened more than low-carbon Stainless Steel rivet at production.
Stainless Steel Rivet -
In general, blind Stainless Steel Rivets are preferred for countless applications: tractors, heavy trucks, garage doors, prefabricated metal buildings, other large assemblies, and white goods, which are consumer goods such as air conditioners, refrigerators, and stoves (at one time these durables were exclusively painted with a white enamel finish, and although they come in countless colors today, they’re still known as “white goods”). Steel blind Stainless Steel Rivet are frequently used in oil and gas applications such as offshore rigs, mining, pipe work, and tank applications because of their durability and 100 percent waterproof seal. Low-carbon steel blind Stainless Steel Rivet are excellent fasteners for containers, construction, and furniture, and high-carbon steel blind Stainless Steel Rivet are frequently used in the aerospace, automotive, and locomotive industries because of their incredible strength and ability to retain their integrity in the toughest environments. Stainless Steel Rivet are popular for use in the transportation and power-generation industries.
Question - Closed Cup waterproof Stainless Steel Rivet?
A long time in testing now released for sale our closed cup Stainless Steel Rivet are the first ones that are 100% waterproof. They are manufactured from a combination of Stainless Steel Rivet AISI 316 / 1.4401 and Duplex AISI 318 L they also incorporate a unique HNBR washer (gasket). HNBR meets the gap left by NBT, EPDM and Neoprene to operate at higher temperatures, resistant to many oils, sour gas and dilute acids with good abrasion resistance it can operate between -30°C to + 150°C (-20°F to + 302°F), Silicon free and UV resistant. The CUP sealed blind rivets are made of 316 Stainless Steel Rivet for the body and the mandrel from 318L Duplex and tested to demonstrate 100% waterproof. To show how they compare we have a video that uses the same size of Stainless Steel Rivet produced in the most popular type of blind Stainless Steel Rivet, these are widely used for metal cladding and jacketing for pipelines and tanks in the oil and gas industry. The video clearly shows the water seeping through the traditional blind or pop rivet, yet our closed cup rivet remains 100% waterproof with up to 1 meter of water. This is key especially in offshore applications were water ingress can easily lead to crevice corrosion resulting in failure of the system and expensive replacement. As a result of these development many future on and offshore projects are expected to propose our closed cup waterproof Stainless Steel Rivet. We can also supply Aluminum rivets, zinc plated rivets, cordless riveting tools and hand rivet tools. These rivets come in many types including standard, multi grip, rainbow (colored), cup, grooved (Rili), star, Tri-go, Tre-go, mass and hammer.
Aluminium Rivet is a permanent mechanical fastener Before being installed, Aluminium rivet consists of a smooth cylindrical shaft with a head on one end. The end opposite to the head is called the tail. On installation, the Aluminium Rivet is placed in a punched or drilled hole, and the tail is upset, or bucked (i.e., deformed), so that it expands to about 1.5 times the original shaft diameter, holding the Aluminium Rivet in place. In other words, the pounding or pulling creates a new "head" on the tail end by smashing the "tail" material flatter, resulting in a Aluminium Rivet that is roughly a dumbbell shape. To distinguish between the two ends of the rivet, the original head is called the factory head and the deformed end is called the shop head or buck-tail.
Because there is effectively a head on each end of an installed rivet, it can support tension loads. However, it is much more capable of supporting shear loads (loads perpendicular to the axis of the shaft).
Fastenings used in traditional wooden boat building, such as copper nails and clinch boalt, work on the same principle as the Aluminium Rivet but were in use long before the term rivet was introduced and, where they are remembered, are usually classified among nails and bolts respectively.What is Aluminum Rivets used for?
|Nominal Size||API 5L GR B|
|Application||Pharmaceutical / Chemical Industry, Construction, Oil & Gas Industry, Automobile Industry|
|Unit Pipe Length||18 meter, 6 meter, 9 meter, 18 m|
|Unit Length||12 m, SEAMLESS PIPES, 6 m|
|Pipe Fluid||Slurry, Gas, Chemical, Water|
|Material Grade||API 5L|
|Alloy Or Not||Iss Alloy|
|Model Number||20 MT|
|Thickness||SEMALESS MANUFACTURING PROCESS|
|Surface Finishing||Mill Finished|
|Type||6MM TO 40 MM|
|Min Outer Dimensions||CARBON STEEL|
|Min Working Capacity||1" NB|
|Is It Corrosion Resistant||Corrosion Resistant|
|Standard||EN 10216-1 P265|
|Bundle Contains||As per customer requirement|
|Is It Customized||Customized|
|Usage/Application||Paper & Pulp Companies,High Pressure Applications,Oil and Gas Industry,Chemical Refinery|
|Features||Corrosion resistant,Accurate dimensions,Can sustain high pressure|
|Other standard||BS 3601 430|
|Surface||APLI 5L GRADE B|
Question - What is API 5L Grade B Seamless Pipes?
Nascent Pipe and Tubes is one of the leading manufacturers, suppliers, exporters, traders and Stock holders of API 5L Grade B Seamless Pipes. API 5L Grade B Seamless Pipes is one of the most common pipe grades used in oil and gas transmission. The API 5L Grade B Seamless Pipes is also known as L245 Pipes, and they come with minimum yield strength of 245MPa. The API 5L Grade B Seamless Pipes is similar to ASTM A106 B or ASTM A53 B material in terms of chemical composition, mechanical properties, and applications. We are one of the top API 5L Grade B ERW Pipe suppliers in India, who manufacture high-quality API 5L Grade B Seamless Pipes to cater to the requirements of our esteemed clients. Our API 5L Grade B Seamless Pipes is widely used in onshore and offshore pipelines. Apart from the seamless variant, we also manufacture API 5L Grade B Welded Pipe. The API 5L Grade B seamless Pipes material is commonly used in the pipeline industries that deal with constructions or liquid/gas transmission. The API 5L Grade B HIC Pipeline is available in two product levels PSL1 and PSL2, and each of them has individual applications. The chemical composition of API 5L Grade B Seamless Pipe PSL2 High Yield Pipe adds to its unique mechanical properties.
API 5L Grade B Seamless Pipes -
API 5L Grade B Seamless Pipes are typically used in the transportation of various fluids and gases. For instance, the specified API 5L Grade B Carbon Steel Pipe is generally used in applications involving industries such as petroleum, petrochemical, as well as the natural gas industries. One such instance, where the API 5L Grade B PSL1 Material proves to be particularly useful is when they are used in sour wells. Addition of elements such as, Molybdenum and chromium can raise the resistance levels of the API 5L Grade B Seamless Pipes to both cracking and corrosion as well. Apart from offering these properties, the API 5L Grade B PSL2 Seamless pipes are known to have a rigid and compact design along with the Grade B Welded Pipe having precise and stable dimensions, properties which make them attractive. Addition of elements such as, Molybdenum and chromium can raise the resistance levels of the API 5L Grade B Seamless Pipes to both cracking and corrosion as well. Apart from offering these properties, the API 5L Grade B PSL2 pipes are known to have a rigid and compact design along with the Grade B Welded Pipe having precise and stable dimensions, properties which make them attractive.
Question - What is Duplex Steel Flanges
Nascent Pipe and Tubes is one of the leading supplier, exporter, traders and stock holder of Duplex Steel Flange. We offers a wide range of Duplex Steel Flanges, which has some excellent features to offer such as Lightweight, Tough construction, dimensionally accurate, and so on. We also offer these products in different grades such as Duplex flanges and Super Duplex Flanges. The granular structure of duplex Steel Flanges is a ferrite-austenite hybrid with a superior strength to weight ratio in comparison to 304 or 316. It balances the weld ability of an austenitic with a pure ferritic and retains decent mechanical toughness in applications with exposure to colder ambient temperatures. Offshore/seawater applications are a common use for this type of steel due to its excellent stress corrosion cracking properties. Therefore, duplex Steel Flanges is often found in desalination and pressure vessel equipment located in port cities.
An austenitic ferritic stainless variant with a higher stress corrosion cracking resistance in comparison to regular austenitic 304 and 316 stainless, but with a lower toughness and impact strength. This category of material includes grades 2205, F51, F53, and F60. Duplex Steel Flanges stainless has increased in popularity over the years due to its excellent chemical and mechanical properties versus their basic stainless counterparts, given especially that the cost differences are minimal now as the availability has increased.
Many types of steel flanges are offered by Nascent Pipe & Tubes of the most used flanges are Duplex Steel Flanges They are the famous supplier and stockiest of all types of Duplex Steel Flanges in India. Stainless steel is highly durable and low-cost alloy. The flanges of Stainless steel are used widely as they have the properties which make it the unbeaten quality material.
Duplex Steel Flanges are hardened alloys and also exceptionally corrosion-resistant. Microstructures of this steel are consist of Ferrite and Austenite phases’ mixture. As a result, they consist of the features of both ferritic and austenitic stainless Steel. It has a high-strength and excellent resistance to corrosion. Duplex Stainless Steel Flanges have excellent intergranular corrosion. It has an outstanding high resistance to corrosion cracking stress even in sulfide and chloride environments.
Duplex Steel Flanges -
Nascent Pipe and Tubes is a widely renowned stocker, supplier, as well as exporter of the best quality of Duplex Steel Flanges to both Indian and international customer base. To make sure that our customers get a variety of high-quality Duplex Steel Flanges to choose from while buying we make use of the best quality of raw material. They are used in off-shore oil drilling companies, used in Aircraft exhaust manifolds, uses in petrochemicals, in power generation, in gas processing, in pharmaceuticals, uses in specialty chemicals, spiral welded tube for burner pipes and fuels, pharmaceutical equipment, heat exchangers, and also in seawater equipment. Double Steel Flanges are available in the many designs like slip-on, weld-neck, blind, threaded, lap joint, and socket weld.
Duplex Steel Weld Neck Raised Face Flanges offers excellent and consistent machining properties for increased cutting speeds, reduced tool wear and set-up times. The formation of intermetallic phases in Duplex Steel Flange Plate Raised Flanges such as sigma phase occurs in the temperature range 600 Degree C - 1000 Degree C and decomposition of ferrite occurs in the range 350 Degree C - 500 Degree C (475 Degree C embrittlement).The basic idea of Duplex Steel Flanges Long Weld Neck Flanges is to produce a chemical composition that leads to an approximately equal mixture of ferrite and austenite.
|Size||As Per Customer''s Requirement|
|Type of Tee||Straight|
|End Connection Type||Threaded|
Reviewed by 42 Users
Most Relevant Reviews